Step 1Drawing / sample
Receive drawing, 3D model or physical sample with quantity and target price.
Precision turned parts, made to your drawing.
Exporting to 25+ countries
BS EN 12164 CW614NASTM B16 C36000IS 319 free-cutting brassISO 965 metric threadsBS EN ISO 228 BSPASME B1.20.1 NPTASME B1.1 UNC / UNFIATF 16949ISO 9001:2015ISO 14001:2015ISO 45001:2018RoHS compliant
- Years of turning experience
- 29+
- Parts per month capacity
- 1.5M
- Machines on the shop floor
- 45+
- Export countries
- 25+
- OEM and trade clients
- 200+
We turn brass, stainless steel, mild steel, copper and aluminium bar into finished components. Turned, threaded, knurled, plated, inspected and packed for your assembly line, from one plant in Gujarat.
What we make
8 product families in brass and engineering metals. Anything not listed can be made to your drawing.
Machining capabilities
From bar to finished component: turning, milling, threading and secondary work, with finishing coordinated and inspected.
How an order moves through the shop
Every order follows the same routing, with an inspection gate before the part moves on.
Step 1PDF DWG STEP
Step 2Engineering review
Check tolerances, threads and material; flag cost drivers; propose process.
Step 3Raw material
Bar stock procured to grade with mill certificate, checked on receipt.
Step 4Machining
Turning, milling and secondary operations on the process chosen for volume.
Step 5In-process inspection
First-off approval, then patrol checks at a fixed frequency on every machine.
Step 6Finishing
Deburring, cleaning and plating as specified, with thickness checked on return.
Step 7Final inspection
Sampling plan against drawing, thread gauging and visual checks before release.
Step 8Packing & dispatch
Counted, labelled and packed for the route, with export documents prepared.
How small is ±0.01 mm?
Hundredths of a millimetre are hard to picture. Here is the full tolerance band drawn to true scale next to things you can hold in your hand.
A 20 µm band is 3.5× narrower than a human hair.
Magnified view, all shapes to the same scale20 µm
±0.01
Critical diameter tolerance
±0.01mm
Length
±0.02 mm
Surface
Ra 0.8 μm
Thread
6g / 6H class
Quality control at every stage
Every job starts with an approved first-off, runs with patrol checks, and is released only after final inspection against the drawing.
Inspection room
- Profile projector
- Surface roughness tester
- Digital height gauge
- Micrometers (outside, inside, bore)
- Thread plug and ring gauges
- Pin gauges and slip gauges
IATF 16949ISO 9001:2015ISO 14001:2015ISO 45001:2018RoHS
How we inspect Materials we machine
Brass, stainless steel, mild steel, copper and aluminium, run from bar on the same machines. Pick a material to load its bar.
CW614N (CuZn39Pb3)
BS EN 12164
01 / 05
Nominal composition, % by weight
- Cu
- 57.0 to 59.0
- Pb
- 2.5 to 3.5
- Fe
- 0.3 max
- Zn
- Remainder
Industries we supply
Hover a sector to see the parts we make for it.
Automotive
Automotive
Sensor housings, fittings, bushes and contact pins for vehicle and aftermarket supply.
- Sensor housings
- Brake and fuel fittings
- Bushes
- Contact pins
HVAC & refrigeration
Energy
Telecom & electronics
Electrical & switchgear
Plumbing & sanitary
Gas & LPG
Agriculture
General engineering
Automotive
Sensor housings, fittings, bushes and contact pins for vehicle and aftermarket supply.
HVAC & refrigeration
Flare nuts, service valve parts and connectors for refrigerant circuits.
Energy
Terminals, busbar connectors and copper contact parts for power distribution and solar installations.
Telecom & electronics
RF connector parts, standoffs and small precision pins for electronic assemblies.
Electrical & switchgear
Terminals, connectors, contact pins and plug pins that carry current reliably.
Plumbing & sanitary
Compression fittings, pipe inserts and bath fitting components that seal reliably at rated pressure.
Gas & LPG
Regulator, meter and CNG fitting components built for pressure and safety.
Agriculture
Sprayer nozzles, irrigation fittings and machine hardware for farm equipment.
General engineering
Build-to-print turned and milled parts for machine builders and OEM assemblies.
Why OEMs work with us
Six reasons buyers give for staying with us after the first order.
Custom development
Send a drawing or a sample. We reverse-engineer, propose tooling and approve a first-off before volume.
First-off sample with a dimensional report
Tight tolerances
Diameters held to hundredths of a millimetre, verified at the machine and again before packing.
Critical diameters to ±0.01 mm
Material flexibility
Free-cutting and DZR brass, stainless, mild steel, aluminium and copper from one supplier.
Six material families, one supplier
Export-ready packing
Part-wise labelling, moisture protection, palletisation and the documents your customs broker asks for.
VCI packing, pallets, certificate of origin
On-time delivery
Capacity planned against your schedule, with dispatch dates confirmed when the order is placed.
Dispatch date confirmed with every order
Engineering on the line
Queries go to the engineer responsible for your part and are answered the same working day.
Same working-day replies
Send us your drawing. Get a quote in 48 hours.
Share the drawing, material and quantity. An engineer reviews it and replies with a costed quote and any notes on tolerances.
Drop your drawing here
PDF DWG DXF STEP JPG PNG